केय म ुहर वभाग-2 हमारा संदभ : सीएमडी-2/16:513...

26
के य मुहर वभाग-2 हमारा संदभ: सीएमडी-2/16:513 (भाग 1 एवं 2) 19 05 2017 वषय: आई एस513 (भाग 1) :2016 के पुनर*+त एस ट आई और अंतरण 1दशा 3नद4श का कायावयनऔर आई एस 513 (भाग 2):2016 के एस ट आई और अंतरण 1दशा 3नद4श का कायावयन सम ाधकार वारा अनुमोदत आई एस 513 (भाग 1) :2016 के पुनर%त एस ट आई और अंतरण दशा +नद,श और आई एस 513 (भाग 2):2016 के एस ट आई और अंतरण दशा +नद,श के त-काल काया01वयनहेतु संल3न है । सभी े7ीय काया0लय8/शाखा काया0लय8से आ;ह है क< इसे अपने अधकार े7 म> ि@थतसभी लाइसे1स धारक8/ आवेक8 को सूचत करे और अनुपालन सु+निDचत करे । (अEण पुछकायला) वैGा+नक-सी 5ी ए. के . भटनागर, वै9ा3नक – एफ और <मुख (सीएमडी-2)(ह>ता/-) सभी े7ीय/शाखा/ काया0लय8 को पIरचाJलत +तJलKप : आई ट एस को बीआईएस इंMानेट पर अपलोड करने के Jलए CENTRAL MARKS DEPARTMENT-2 Our Ref: CMD-2/16 513 (Pt 1 & Pt 2) 19 05 2017 Subject: Switchover guidelines for implementation of IS 513 (Part 1):2016 and guidelines for implementation of IS 513 (Part 2):2016. Please find enclosed switch over guidelines for implementation of IS 513 (Part 1):2016 and guidelines for implementation of IS 513 (Part 2) 2016, duly approved by Competent Authority, for immediate implementation. ROs/BOs are requested to kindly bring to the notice of licensees/ applicants under their jurisdictions and ensure compliance to implementation of the above guidelines. (Arun Pucchakayala) Scientist C Shri A. K. Bhatnagar, Scientist – F & Head (CMD-2)(sd/-) All ROs/BOs Copy to : ITS for hosting on BIS Intranet.

Upload: others

Post on 05-Aug-2020

2 views

Category:

Documents


0 download

TRANSCRIPT

Page 1: केय म ुहर वभाग-2 हमारा संदभ : सीएमडी-2/16:513 (भाग 1 एवं 2) 19 … · In IS 513 (part2):2016, for automobile and engineering

के� ��य मुहर �वभाग-2

हमारा संदभ�: सीएमडी-2/16:513 (भाग 1 एवं 2) 19 05 2017

�वषय: आई एस513 (भाग 1) :2016 के पुनर�*+त एस ट� आई और अतंरण 1दशा 3नद4श का काया��वयनऔर आई एस

513 (भाग 2):2016 के एस ट� आई और अंतरण 1दशा 3नद4श का काया��वयन

स�म �ा�धकार� �वारा अनुमो�दत आई एस 513 (भाग 1) :2016 के पुनर�%�त एस ट� आई और अंतरण �दशा +नद,श और

आई एस 513 (भाग 2):2016 के एस ट� आई और अंतरण �दशा +नद,श के त-काल काया01वयनहेतु संल3न है ।

सभी �े7ीय काया0लय8/शाखा काया0लय8स ेआ;ह है क< इसे अपने अ�धकार �े7 म> ि@थतसभी लाइसे1स धारक8/ आवे�क8 को

सू�चत करे और अनुपालन सु+निDचत करे ।

(अEण पुछकायला)

वैGा+नक-सी

5ी ए. के. भटनागर, वै9ा3नक – एफ और <मुख (सीएमडी-2)(ह>ता/-)

सभी �े7ीय/शाखा/ काया0लय8 को पIरचाJलत

�+तJलKप : आई ट� एस को बीआईएस इंMानेट पर अपलोड करने के Jलए

CENTRAL MARKS DEPARTMENT-2

Our Ref: CMD-2/16 513 (Pt 1 & Pt 2) 19 05 2017

Subject: Switchover guidelines for implementation of IS 513 (Part 1):2016 and guidelines for

implementation of IS 513 (Part 2):2016.

Please find enclosed switch over guidelines for implementation of IS 513 (Part 1):2016 and guidelines for

implementation of IS 513 (Part 2) 2016, duly approved by Competent Authority, for immediate

implementation.

ROs/BOs are requested to kindly bring to the notice of licensees/ applicants under their jurisdictions and

ensure compliance to implementation of the above guidelines.

(Arun Pucchakayala)

Scientist C

Shri A. K. Bhatnagar, Scientist – F & Head (CMD-2)(sd/-)

All ROs/BOs

Copy to : ITS for hosting on BIS Intranet.

Page 2: केय म ुहर वभाग-2 हमारा संदभ : सीएमडी-2/16:513 (भाग 1 एवं 2) 19 … · In IS 513 (part2):2016, for automobile and engineering

CENTRAL MARKS DEPARTMENT -2

Our Ref: CMD-2/16: IS 513(pt.1) & (pt.2) 18-05-2017

Subject: Guidelines for switchover of licences held as per IS 513:2008 to IS 513 (Pt-1):2016

& for implementation of IS 513(Pt-2):2016

1. Indian Standard IS 513:2008 has been revised and published in two parts as

follows:

Old Standard Revised Standard

IS 513:2008, Cold Reduced Low Carbon

Steel Sheet and Strip

IS 513(Pt-1):2016, Cold Reduced

Carbon Steel Sheet and Strip Part 1

Cold Forming and Drawing Purpose

IS 513(Pt-2):2016, Cold Reduced

Carbon Steel Sheet and Strip Part 2

High tensile and multi-phase steel

2. In view of the above revision, the following new STIs have been issued:

Standard STI

IS 513(Pt-1):2016 Doc:STI/513 (Part 1)/11 April 2017

(Annex-1). This STI replaces

Doc:STI/513/10 September 2016 as per

IS 513:2008

IS 513 (Pt-2):2016 Doc:STI/513 (Part 2)/1 April 2017

(Annex-2)

3. In IS 513 (part1):2016,for cold forming and drawing applications, new grades along with

existing grades of IS 513:2008 have been introduced.

4. In IS 513 (part2):2016, for automobile and engineering applications, new grades of High

tensile and multi-phase steel sheet and strips have been introduced.

5. The modifications made in IS 513 (Part 1): 2016 and IS 513 (part-2): 2016 are listed at

Annex -3, for general guidance.

6. IS 513:2008 stands cancelled after 15th

December 2017 as per the gazette notification.

7. The existing licences as per IS 513:2008 have to be endorsed for changeover to

IS 513(Part 1): 2016, by 15th

December 2017.

8. For use of standard mark on grades covered under IS 513(Part 2): 2016, manufacturers

are required to submit application with fee for new licence.

9. In order to switchover from IS 513:2008 to IS 513 (part 1) & (part 2), following actions

need to be completed by the licensees at the latest by 01 December 2017:

i) Existing Licensees as per IS 513:2008 shall submit the following: a) acceptance to STI (Doc: STI/513 (Part 1)/ 11 April 2017), b) acceptance to Marking fee as per IS 513(pt-1):2016 (rates same as that of

IS 513:2008) c) CMD/PF 306 confirming availability of testing equipments as per

IS 513(pt-1):2016:

Page 3: केय म ुहर वभाग-2 हमारा संदभ : सीएमडी-2/16:513 (भाग 1 एवं 2) 19 … · In IS 513 (part2):2016, for automobile and engineering

d) Evidence of conformity as indicated below for the designations covered in the scope of existing licence:

Designation in the

existing licence

Evidence of conformity (as per

IS 513(Pt.1) : 2016)

CR0 factory test report or test report from BIS recognized Lab

CR1 factory test report or test report from BIS recognized Lab, for any one temper designation

CR5 *Test report from BIS recognized lab (see note)

CR2,CR3,CR4 Not required

ii) For inclusion of other grades which are not covered in the scope of licence, requests for inclusion may be submitted to the BO.

iii) Switchover of Licences held as per IS 513:2008 to IS 513(part 1):2016 shall be complete by 15 December 2017.

10. For Switchover of Licences held as per IS 513:2008 to IS 513(part 1 & (part2) the

following actions are to be ensured by the BOs:

i. All BOs shall inform Applicants and Licensees under their jurisdiction about the revision of the Standard.

ii. BOs shall ensure that no licence as per IS 513:2008 is under operation after 15 December 2017.

iii. BO may issue endorsement in respect of the licence suitably on receipt of documents as mentioned above from the licensee, confirming implementation of the revised Standard.

iv. In case any licensee fails to complete all the above actions by 15th

December 2017, further necessary action as per OMPC 2004 (with all amendments) and guidelines on Stoppage and Resumption of Marking ref:CMD-1/2:1 dtd: 01 Dec 2016, shall be initiated by the concerned BO.

v. For all those grades as per IS 513(part 1):2016, which are not covered in the licence, inclusion of new varieties can be processed based on the request of the licensee as per the grouping guidelines (Annex-4) and as per the existing procedure of OMPC.

vi. Inform Licensees of IS 513:2008, interested in obtaining new licence for IS 513(part-2):2016, to submit application along with fee and the following:

a) undertaking on letter head that they can produce and test the product as per IS 513(part-2):2016 with the existing facilities already verified by BIS as per IS 513:2008

b) *Test report from BIS recognized lab (see Note and Annex-5)

c) Acceptance to STI as per IS 513(pt.2):2016 d) Acceptance to MF as per IS 513(pt.2):2016(will be notified shortly) e) payment of prescribed advance minimum marking fee f) Self evaluation-cum-verification report(Section-A only)

Page 4: केय म ुहर वभाग-2 हमारा संदभ : सीएमडी-2/16:513 (भाग 1 एवं 2) 19 … · In IS 513 (part2):2016, for automobile and engineering

vii. Applications received as above shall be processed for grant of licence without

need for carrying out visit prior to grant of licence as the facilities were already verified at the time of GOL as per IS 513:2008. BOs shall make efforts for

arranging an early surveillance inspection during which detailed verification of the existing process and product can be made alongwith revalidation of the

manufacturing capabilities.

*Note: Till such time laboratories having test facilities as per IS 513(part-1):2016 / IS 513(part-2):2016 are recognized, test reports from BIS recognized laboratories, which are

recognized as per IS 513:2008, shall be accepted. If complete testing of the product is not possible in one lab, the product may be tested in any combination of laboratories (outside/in-

house).

11. In case of applications which are under process as per IS 513:2008, the following actions are

required to be taken by BOs:

i. On receipt of requests from applicants opting for considering their application as per the revised Standard IS 513(pt.1):2016, the application is to be processed as per

IS 513(pt.1):2016. In such cases the applicant shall be required to submit an undertaking that in no circumstances their application shall be considered as per IS

513:2008. ii. Applications recorded under normal procedure where samples are yet to be drawn

for independent testing shall be processed only as per the revised Standard IS 513 (part

1):2016. iii. Wherever the application is at final stage of GOL (i.e. TR received/sample drawn

and TR awaited), the licence shall be granted as per the version of standard indicated in test reports. However, such licensee shall be advised to complete actions for switch

over to the revised version of standard by 01 December 2017. iv. A declaration shall be obtained from all Applicants, for applications being processed

as per the old Standard that they will switch over to the revised Standard IS 513 (part 1):2016 by 01 December 2017.

12. Fresh applications shall be processed only as per the revised Standards IS 513 (part 1):2016 & IS 513 (part 2):2016.

13. Beyond 15 December 2017 no Licence shall be granted as per the old Standard IS 513:2008. 14. The above guidelines shall come into force with immediate effect

Encl: As above

(Arun Pucchakayala)

Scientist C,CMD-2

Head (CMD-2) (sd/-)

DDG(Cert.) (sd/-)

All ROs/BOs

Page 5: केय म ुहर वभाग-2 हमारा संदभ : सीएमडी-2/16:513 (भाग 1 एवं 2) 19 … · In IS 513 (part2):2016, for automobile and engineering

Doc : STI/513(Pt.1)/ 11, April 2017

1

SCHEME OF TESTING AND INSPECTION FOR CERTIFICATION OF

COLD REDUCED CARBON STEEL SHEET AND STRIP

PART 1 COLD FORMING AND DRAWING PURPOSE

ACCORDING TO IS 513 (part 1):2016 (Sixth Revision) 1 LABORATORY - A laboratory shall be maintained which shall be suitably equipped and

staffed, where the tests shall be carried out in accordance with the methods given in the

specification. 1.1 All testing apparatus/measuring instruments shall be periodically checked, verified and

calibrated as appropriate and records of such checks/verification, calibration shall be

maintained.

1.2 Periodic calibration shall be done on the tensile testing machine. The frequency of

such calibration should preferably be once in six months, and in any case, not more

than once in a year.

2 TEST RECORDS - All records of tests as per this scheme of testing and inspection shall be

kept in suitable forms. 2.1 Copies of any records or charts that may be required by BIS shall be made available at any

time on request. 3. QUALITY CONTROL – It is recommended that, as far as possible, Statistical Quality

Control (SQC) methods may be used for controlling quality of the product during production as

envisaged in this scheme [See IS 397 (Part 1), IS 397 (Part 2) and IS 397 (Part 3)]. 3.1 In addition efforts should be made to gradually introduce the Quality Management

System in accordance with IS/ISO 9001. 4. STANDARD MARK - The Standard Mark, as given in Column (1) of the first schedule of the

licence, as specified for cold rolled carbon steel sheets and strips as per IS 513(part 1):2016 shall

be legibly marked on top of each package of sheets and strips. 4.1TEST CERTIFICATE – For each consignment of BIS Certified material conforming to IS

513(part 1):2016 there shall be a test certificate which shall contain the Standard Mark, the cast

number, Control Unit number, designation, grade and the corresponding test results (as given in

Annexure I).

4.2 MARKING – The following shall be legibly marked on the top of each bundle or package of

sheets and strips or shown on a tag attached to each coil :

a) Manufacturer’s name or trade mark,

b) Nomenclature of grade Quality

c) Product dimensions,

d) Cast or identification mark by which the sheet or strip may be traced to the cast or casts from

which they were made,

e) Mass/Net weight and

f) Date of manufacture

g) Licence No. (CM/L….)

Annex-1

Page 6: केय म ुहर वभाग-2 हमारा संदभ : सीएमडी-2/16:513 (भाग 1 एवं 2) 19 … · In IS 513 (part2):2016, for automobile and engineering

Doc : STI/513(Pt.1)/ 11, April 2017

2

h) temper

i) surface finish designation

4.3 SUPPLY OF MATERIAL AND DELIVERY CONDITIONS - The material shall meet the

requirements of clause 4 and 13 of the specification. 4.3.1 PACKING - Each sheet shall be treated on both sides with non-hardening type

preventive oil which can be easily washed with aqueous alkali solution. The product may be

ordered “not oiled” if required [Ref. cl.9.6 of IS 513(part 1):2016].

4.3.2 Sheets and strips shall be supplied in bundles or packages not weighing more than 3

tonnes or as agreed to between the purchaser and the manufacturer.

4.3.3 Sheets and strips shall be securely packed in waterproof material and covered all over

with steel envelope and securely tied round with steel straps and preferably with wooden battens

underneath to prevent the sheets from rusting and damage during transit. 5. LEVELS OF CONTROL : Inspection and tests at various levels of control specified in

Table 1 shall be carried out on all quantities of steel intended to be covered under this scheme

and appropriate records as per para 2 and charts as per para 3 of this STI shall be maintained.

All production which conforms to the Indian Standard and covered by the licence shall be

marked with BIS Standard Mark. 5.1 METHOD OF MANUFACTURE – The method of manufacture of Steel for sheets and

strips shall be left at the discretion of the manufacturer.

5.2 CONTROL UNIT: For the purpose of this scheme, 50 tonnes of material or part thereof

representing the same cast, grade quality and heat-treatment (if any) rolled to same thickness and

processed in same condition shall constitute a control unit.

5.3 Sheets and strips shall be supplied rimmed, semi-killed or killed condition as agreed to

between the purchaser and the manufacturer. However, grades supplied in delayed ageing and

non-ageing guarantee shall be supplied only in fully aluminium killed or in a fully stabilized

condition.

5.4 On the basis of tests and inspection results, decision regarding conformity or otherwise of lots

of steel to the requirements of the specification shall be taken as indicated below: 5.5 CHEMICAL COMPOSITION - Chemical composition (Ladle analysis) obtained by

analyzing one sample from each heat shall conform to the requirements laid down in Table 3 of

the specification. Product analysis shall be carried out at the rate of one from every cast and the

permissible variation in the case of product analysis shall be as laid down in Table 4 of the

specification. The analysis of the steel shall be carried out according to IS 228 and its relevant

parts or any other established instrumental/chemical method. In case of dispute the procedure

given in IS 228 and its relevant parts shall be referee method. The manufacturer shall declare the

established instrumental method adopted for chemical analysis, details of the reference material

accompanied with test certificate used for its calibration and frequency of calibration.

Page 7: केय म ुहर वभाग-2 हमारा संदभ : सीएमडी-2/16:513 (भाग 1 एवं 2) 19 … · In IS 513 (part2):2016, for automobile and engineering

Doc : STI/513(Pt.1)/ 11, April 2017

3

5.6 RETEST - If a test does not give the specified results, two additional tests shall be carried out

at random on the same lot. Both retests shall conform to the requirements of this standard,

otherwise, the control unit shall be rejected.

6. REJECTIONS - Records shall be maintained for a reasonable time from which information

relating to the rejection of material which does not conform to IS 513(part 1):2016 may be

obtained. Such rejected material shall not in any case be mixed up with that conforming to this

specification.

7 SAMPLES - The licensee shall supply, free of charge, the samples required in accordance with

Regulation of the Bureau of Indian Standards from his factory or godown. BIS may procure

samples from open market. 8.0 REPLACEMENT - Whenever a complaint is received soon after the goods with Standards

Mark have been purchased and used, and if there is adequate evidence that the goods have not

been misused, defective goods shall be replaced free of cost by the licensee in case the complaint

is proved to be genuine and the warranty period ( where applicable ) has not expired. The final

authority to judge conformity of the product to the Indian standards shall be with the Bureau. The

firm shall have own complaint investigation system as per IS/ISO 10002.

8.1 In the event of any damage caused by the goods bearing the Standard Mark, or claim

being filed by the consumers against BIS Standards Mark and not "conforming to" the relevant

Indian Standard, entire liability arising out of such non conforming product shall be of the

licensee and BIS shall not in any way be responsible in such cases.

9. STOP MARKING - The marking of the product shall be stopped under intimation to the

Bureau if, at any time, there is any difficulty in maintaining the conformity of their product to the

specification, or the testing equipment goes out of order or for any reason. The marking may be

resumed as soon as the defects are removed under intimation to BIS. The licensee shall

implement the provisions of self-stoppage of Marking as mentioned in BIS Act, Rules

and Regulations. 9.1 The marking of the product shall be stopped immediately if directed to do so by Bureau for

any reason. The marking may then be resumed only after permission by the Bureau. The

information regarding resumption of markings shall also be sent to the Bureau.

10 PRODUCTION DATA - The licensee shall send to BIS a statement of quantity produced,

marked and exported and the value thereof at the end of each operative year of the licence as per

the enclosed proforma which has to be authenticated by a Chartered Accountant.

Table 1…..

Page 8: केय म ुहर वभाग-2 हमारा संदभ : सीएमडी-2/16:513 (भाग 1 एवं 2) 19 … · In IS 513 (part2):2016, for automobile and engineering

Doc : STI/513(Pt.1)/ 11, April 2017

4

IS 513(part 1):2016, COLD REDUCED CARBON STEEL SHEET AND STRIP

PART 1 COLD FORMING AND DRAWING PURPOSE

TABLEL 1 (LEVELS OF CONTROL),

(Para 5 of the Scheme of Testing and Inspection)

TEST DETAILS LEVELS OF CONTROL REMARKS

Cl Requirement Test Method No. of samples Lot size Frequency

Clause Reference

7 Chemical

Composition

IS 228 or any other established instr/ Chem. Method. Alternatively, the method specified in relevant ISO/IEC standard

may be used.

a) Ladle Analysis 7.1

7.2

Table 3

IS 513(part

1):2016

IS 228

One

Each Heat

Each Heat Applicable for primary steel

producers only

b) Product Analysis

7.3

Table 4

IS 513(part

1):2016

i) One

ii) One

i) Each Cast

ii) Each Cast

i) Each Cast

ii) Each

Cast

i) Applicable for primary

steel producers with steel

making and both hot & cold

rolling facilities

ii) In case of Re-rollers with

cold-rolling facilities, no

further testing is required if

the material obtained from

primary producers of steel is

ISI marked and received with

test certificate.

8 Mechanical and

Physical Properties

8.1 Tensile Test 8.1.1,

8.1.2,8.1.3 ,

8.1.4 & 8.1.5

Table 5A,5B,

5C

IS 513(part

1):2016

IS 1608

One 50 tonnes or less Each

Control

Unit

To be carried out only if

specified by the purchaser

8.2 Cupping Test 8.2

Fig.1

IS 513(part

1):2016

IS 10175

One -do- -do- Applicable for steel grades of

quality CR2, CR3, CR4

subject to mutual agreement

between purchaser and

manufacturer.

Page 9: केय म ुहर वभाग-2 हमारा संदभ : सीएमडी-2/16:513 (भाग 1 एवं 2) 19 … · In IS 513 (part2):2016, for automobile and engineering

Doc : STI/513(Pt.1)/ 11, April 2017

5

8.3 Hardness Test 8.3

Table 6

IS 513(part

1):2016

IS 1586

One -do- -do- Applicable for steel grades of

quality CR0, CR1.

8.4 Bend Test 8.4.1,

8.4.2,8.4.3 &

8.4.4

Table 7

IS 513(part

1):2016

IS 1599

One -do- -do-

8.5 Plastic Strain Ratio 8.5.1

8.5.2

Table 5A,5B,

5C

IS 513(part

1):2016

IS 11999

One -do- -do-

8.6 Tensile strain hardening component

8.6.1

8.6.2

Table 5A,5B,

5C

IS 513(part

1):2016 IS 15756

One -do- -do-

8.7 Bake hardening Index

8.7

Annex B

Table 5B,5C

IS 513(part

1):2016

One -do- -do- Applicable only for steel

designation- Bake hardening

5. Non-ageing characteristics

5.1, 5.2& 5.3

Table 2

IS 513(part

1):2016

- - Each

Control

Unit

Applicable for steel grades of

CR2, CR3, delay ageing

quality and non-ageing

quality.

9

Surface condition 9.1,9.2,9.3,

9.4

IS 513(part

1):2016

As agreed between the purchaser and the supplier.

9.5 Surface Finish 9.5.1, 9.5.2

& 9.5.3

IS 513(part

1):2016

IS 15262

As agreed between the purchaser and the supplier.

10

Freedom from defects

10.1,10.2

&10.3

IS 513(part

1):2016

Adequate inspection to ensure each item to be free from

defects

11 Dimensions &

Tolerances

11.1,11.2 &

11.3

IS 513(part

1):2016

IS/ISO16162

Adequate inspection to ensure each item to be within the

limits of specification.

Page 10: केय म ुहर वभाग-2 हमारा संदभ : सीएमडी-2/16:513 (भाग 1 एवं 2) 19 … · In IS 513 (part2):2016, for automobile and engineering

Doc : STI/513(Pt.1)/ 11, April 2017

6

4 Supply of material 4.1,4.2 &4.3 IS 513(part

1):2016

As agreed to between the purchaser and the supplier Records of mechanical

properties as agreed to

between purchaser and the

manufacturer as per cl.4.3

of ISS shall be maintained.

13.3 Packing 13.3

9.6

Table 9

IS 513(part

1):2016

Each Sheet/strip shall be treated on both sides with non-

hardening type rust preventive oil, which can be easily

washed with aqueous alkali solution.

i) Weight of sheets and

strips in bundles or

packages shall be as agreed

to between the purchaser

and the manufacturer.

ii) The product may not be

oiled, only if required by

the purchaser.

Page 11: केय म ुहर वभाग-2 हमारा संदभ : सीएमडी-2/16:513 (भाग 1 एवं 2) 19 … · In IS 513 (part2):2016, for automobile and engineering

Doc : STI/513(Pt.1)/ 11, April 2017

7

ANNEXURE-I (Para 4.1 of the Scheme of Testing and Inspection)

XYZ IRON AND STEEL COMPANY

(Registered office Address and works address) TEST CERTIFICATE FOR COLD REDUCED CARBON STEEL SHEET AND STRIP PART 1 COLD FORMING AND DRAWING PURPOSE

TEST CERTIFICATE No.________________________________________________________________________________DATE_________ To M/s_____________________________________________________________________________________________________________

It is certified that the material described below fully conforms to IS 513(part 1):2016 Chemical composition and Mechanical

properties of the product, as tested in accordance with the Scheme of Testing and Inspection contained in the BIS Certification Marks

Licence No.CM/L_____________________ are as indicated below against each order No. etc.

(PLEASE REFER TO IS 513(part1):2016 FOR DETAILS OF SPECIFICATION REQUIREMENTS)

TEST RESULTS

Ord

er

No.

Di

me

nsi

ons

Cast

No. &

C.U.

No.

Nomen

clature

of steel

grade

quality

Quan

tity

(Ton

nes)

Chemical Analysis Erichsen

Cupping

Test

hardness

BH

index

+Mechanical Properties r n Non-

ageing

character

istics

Condition

& Finish

C

(%) Al

(%) **

Cu

(%)

S

(%)

P

(%)

N

(%)

Yield Stress

(N/mm2)

Tensile

Strength

(N/mm2)

Elongation

(%)

The material supplied conforms to the stipulated rolling tolerances. ** For Copper bearing quality + If specified by the purchaser Remarks:

SIGNATURE DESIGNATION FOR XYZ

IRON & STEEL COMPANY

(It is suggested that size A-4 paper (210X297) be used for this certificate)

BIS

STANDARD

MARK

Page 12: केय म ुहर वभाग-2 हमारा संदभ : सीएमडी-2/16:513 (भाग 1 एवं 2) 19 … · In IS 513 (part2):2016, for automobile and engineering

DOC: STI/513(Pt.1)/11 April 2017

PROFORMA FOR OBTAINING PRODUCTION DETAILS

Period covered

Name of Licensee

Name of Articles (s) IS No.

Grade/Type/Size/Variety/Class/Rating

Brand/Trade/Name(s) of Product covered under BIS Certification Mark

Total production of the articles(s) licensed for certification marking

Total production of the article(s) conforming to Indian Standard

Production covered with BIS Certification Mark and its Value :

a) Quantity

Brand Name used on production covered under BIS Certification Mark

Calculation of marking fee on unit-rate basis; Marking Fee per unit

a) Unit

b) Quantity covered with BIS Certification Mark

c) Marking fee rounded off in whole rupees as obtained by applying unit rates given in (a) on quantity

given in (b)

Quantity not covered with BIS Certification Mark, if any.

Reasons for such non-coverage

Brand Name under which non-ISI goods were sold

Quantity exported with BIS Standard Mark and its value

Brand Name under which BIS Certified goods are exported

Authentication by Chartered Accountant

8

Page 13: केय म ुहर वभाग-2 हमारा संदभ : सीएमडी-2/16:513 (भाग 1 एवं 2) 19 … · In IS 513 (part2):2016, for automobile and engineering

Doc : STI/513(Pt.2)/ 1, April 2017

1

SCHEME OF TESTING AND INSPECTION FOR CERTIFICATION OF

COLD REDUCED CARBON STEEL SHEET AND STRIP

PART 2 HIGH TENSILE AND MULTI-PHASE STEEL

ACCORDING TO IS 513 (part 2):2016 (Sixth Revision)

1 LABORATORY - A laboratory shall be maintained which shall be suitably equipped and

staffed, where the tests shall be carried out in accordance with the methods given in the

specification. 1.1 All testing apparatus/measuring instruments shall be periodically checked, verified and

calibrated as appropriate and records of such checks/verification, calibration shall be

maintained.

1.2 Periodic calibration shall be done on the tensile testing machine. The frequency of

such calibration should preferably be once in six months, and in any case, not more

than once in a year.

2 TEST RECORDS - All records of tests as per this scheme of testing and inspection shall be

kept in suitable forms. 2.1 Copies of any records or charts that may be required by BIS shall be made available at any

time on request. 3. QUALITY CONTROL – It is recommended that, as far as possible, Statistical Quality

Control (SQC) methods may be used for controlling the quality of the product during production

as envisaged in this scheme [See IS 397 (Part 1), IS 397 (Part 2) and IS 397 (Part 3)]. 3.1 In addition efforts should be made to gradually introduce the Quality Management

System in accordance with IS/ISO 9001. 4 STANDARD MARK - The Standard Mark, as given in Column (1) of the first schedule of the

licence, as specified for cold rolled carbon steel sheets and strips as per IS 513(part 2):2016 shall

be legibly marked on top of each package of sheets and strips. 4.1 TEST CERTIFICATE – For each consignment of BIS Certified material conforming to

IS 513(part 2):2016 there shall be a test certificate which shall contain the Standard Mark, the

cast number, Control Unit number, designation, grade and the corresponding test results (as given

in Annexure I). 4.2 MARKING – The following shall be legibly marked on the top of each bundle or

package of sheets and strips or shown on a tag attached to each coil : a) Manufacturer’s name or trade mark, b) Nomenclature of grade Quality c) Product dimensions,

Annex-2

Page 14: केय म ुहर वभाग-2 हमारा संदभ : सीएमडी-2/16:513 (भाग 1 एवं 2) 19 … · In IS 513 (part2):2016, for automobile and engineering

Doc : STI/513(Pt.2)/ 1, April 2017

2

d) Cast or identification mark by which the sheet or strip may be traced to the cast or casts from

which they were made,

e) Mass/Net weight and

f) Date of manufacture

g) Licence No. (CM/L….)

h) surface finish designation

4.3 SUPPLY OF MATERIAL AND DELIVERY CONDITIONS - The material shall meet the

requirements of clause 4 and 12 of the specification. 4.3.1 PACKING - Each sheet shall be treated on both sides with non-hardening type

preventive oil which can be easily washed with aqueous alkali solution. The product may be

ordered “not oiled” if required [Ref. cl.8.6 of IS 513(part 2):2016].

4.3.2 Sheets and strips shall be supplied in bundles or packages not weighing more than 3

tonnes or as agreed to between the purchaser and the manufacturer.

4.3.3 Sheets and strips shall be securely packed in waterproof material and covered all over

with steel envelope and securely tied round with steel straps and preferably with wooden battens

underneath to prevent the sheets from rusting and damage during transit. 5. LEVELS OF CONTROL : Inspection and tests at various levels of control specified in

Table 1 shall be carried out on all quantities of steel intended to be covered under this scheme

and appropriate records as per para 2 and charts as per para 3 of this STI shall be maintained.

All production which conforms to the Indian Standard and covered by the licence shall be

marked with BIS Standard Mark.

5.1 METHOD OF MANUFACTURE – The method of manufacture of Steel for sheets and

strips shall be left at the discretion of the manufacturer.

5.2 CONTROL UNIT: For the purpose of this scheme, 50 tonnes of material or part thereof

representing the same cast, grade quality and heat-treatment (if any) rolled to same thickness and

processed in same condition shall constitute a control unit.

5.3 Sheets and strips shall be supplied rimmed, semi-killed or killed condition as agreed to

between the purchaser and the manufacturer. 5.4 On the basis of tests and inspection results, decision regarding conformity or otherwise of lots

of steel to the requirements of the specification shall be taken as indicated below: 5.5 CHEMICAL COMPOSITION - Chemical composition (Ladle analysis) obtained by

analyzing One sample from each heat shall conform to the requirements laid down in Table 2 of

the specification. Product analysis shall be carried out at the rate of one from every cast and the

permissible variation in the case of product analysis shall be as laid down in Table 3 of the

specification. The analysis of the steel shall be carried out according to IS 228 and its relevant

parts or any other established instrumental/chemical method. Alternatively, the method specified

Page 15: केय म ुहर वभाग-2 हमारा संदभ : सीएमडी-2/16:513 (भाग 1 एवं 2) 19 … · In IS 513 (part2):2016, for automobile and engineering

Doc : STI/513(Pt.2)/ 1, April 2017

3

in relevant ISO standard may be used. In case of dispute the procedure given in IS 228 and its

relevant parts shall be referee method. The manufacturer shall declare the established

instrumental method adopted for chemical analysis, details of the reference material accompanied

with test certificate used for its calibration and frequency of calibration.

5.6 RETEST - If a test does not give the specified results, two additional tests shall be carried out

at random on the same lot. Both retests shall conform to the requirements of this standard,

otherwise, the control unit shall be rejected.

6. REJECTIONS - Records shall be maintained for a reasonable time from which information

relating to the rejection of material which does not conform to IS 513(part 2):2016 may be

obtained. Such rejected material shall not in any case be mixed up with that conforming to the

specification.

7 SAMPLES - The licensee shall supply, free of charge, the samples required in accordance with

Regulation of the Bureau of Indian Standards from his factory or godown. BIS may procure

samples from open market. 8.0 REPLACEMENT - Whenever a complaint is received soon after the goods with Standards

Mark have been purchased and used, and if there is adequate evidence that the goods have not

been misused, defective goods shall be replaced free of cost by the licensee in case the complaint

is proved to be genuine and the warranty period ( where applicable ) has not expired. The final

authority to judge conformity of the product to the Indian standards shall be with the Bureau. The

firm shall have own complaint investigation system as per IS/ISO 10002. 8.1 In the event of any damage caused by the goods bearing the Standard Mark, or claim

being filed by the consumers against BIS Standards Mark and not "conforming to" the relevant

Indian Standard, entire liability arising out of such non conforming product shall be of the

licensee and BIS shall not in any way be responsible in such cases. 9. STOP MARKING - The marking of the product shall be stopped under intimation to the

Bureau if, at any time, there is any difficulty in maintaining the conformity of their product to the

specification, or the testing equipment goes out of order or for any reason. The marking may be

resumed as soon as the defects are removed under intimation to BIS. The licensee shall

implement the provisions of self-stoppage of Marking as mentioned in BIS Act, Rules

and Regulations. 9.1 The marking of the product shall be stopped immediately if directed to do so by Bureau for

any reason. The marking may then be resumed only after permission by the Bureau. The

information regarding resumption of markings shall also be sent to the Bureau.

10 PRODUCTION DATA - The licensee shall send to BIS a statement of quantity produced,

marked and exported and the value thereof at the end of each operative year of the licence as per

the enclosed proforma which has to be authenticated by a Chartered Accountant.

Table 1.…..

Page 16: केय म ुहर वभाग-2 हमारा संदभ : सीएमडी-2/16:513 (भाग 1 एवं 2) 19 … · In IS 513 (part2):2016, for automobile and engineering

Doc : STI/513(Pt.2)/ 1, April 2017

4

IS 513(part 2):2016, COLD REDUCED CARBON STEEL SHEET AND STRIP

PART 2 HIGH TENSILE AND MULTI-PHASE STEEL

TABLEL 1 (LEVELS OF CONTROL),

(Para 5 of the Scheme of Testing and Inspection)

TEST DETAILS LEVELS OF CONTROL REMARKS

Cl Requirement Test Method No. of samples Lot size Frequency

Clause Reference

6 Chemical

Composition

IS 228 or any other established instr/ Chem. Method. Alternatively, the method specified in relevant ISO/IEC standard

may be used.

a) Ladle Analysis 6.a

6.b

Table 2

IS 513(part

2):2016

IS 228

One

Each Heat Each Heat Applicable for primary steel

producers only

b) Product Analysis

6.c

Table 3

IS 513(part

2):2016

i) One

ii) One

i) Each Cast

ii) Each Cast

i)Each Cast

ii)Each

Cast

i) Applicable for primary

steel producers with steel

making and both hot & cold

rolling facilities

ii) In case of Re-rollers with

cold-rolling facilities only, no

further testing is required if

the material obtained from

primary producers of steel is

ISI marked and received with

test certificate.

7 Mechanical and

Physical Properties

7.1 Tensile Test 7.1.1,

7.1.2,7.1.3 ,

& 7.1.4

Table 4A,4B

IS 513(part

2):2016

IS 1608

One 50 tonnes or less Each

Control

Unit

To be carried out only if

specified by the purchaser

7.2 Bend Test 7.2.1,

7.2.2,7.2.3 &

7.2.4

Table 5

IS 513(part

2):2016

IS 1599

One -do- -do-

Page 17: केय म ुहर वभाग-2 हमारा संदभ : सीएमडी-2/16:513 (भाग 1 एवं 2) 19 … · In IS 513 (part2):2016, for automobile and engineering

Doc : STI/513(Pt.2)/ 1, April 2017

5

7.3 Tensile strain hardening component

7.3.1

7.3.2

Table 4A,4B

IS 513(part

2):2016 IS 15756

One 50 tonnes or less Each

Control

Unit

8 Surface Finish

8.4 Surface Condition 8.4.1

8.4.2

8.4.3

8.4.4

8.4.5

IS 513(part

2):2016

Adequate inspection to ensure each item is supplied

either of the surface qualities A or B

8.5 Surface Finish 8.5.1

8.5.2

8.5.3

Table 6

IS 513(part

2):2016

One Each Sheet/strip Each

Sheet/strip

9

Freedom from defects

9.1,9.2 &9.3 IS 513(part

2):2016

Adequate inspection to ensure each item to be free from

defects

10 Dimensions &

Tolerances

10.1,10.2 &

10.3

IS 513(part

2):2016

IS/ISO16162

Adequate inspection to ensure each item to be within the

limits of specification.

12 Packing 12.3

8.6

Table 7

IS 513(part

2):2016

Each Sheet/strip shall be treated on both sides with non-

hardening type rust preventive oil, which can be easily

washed with aqueous alkali solution.

i) Weight of sheets and

strips in bundles or

packages shall be as agreed

to between the purchaser

and the manufacturer.

ii) The product may not be

oiled, only if required by

the purchaser.

Page 18: केय म ुहर वभाग-2 हमारा संदभ : सीएमडी-2/16:513 (भाग 1 एवं 2) 19 … · In IS 513 (part2):2016, for automobile and engineering

Doc : STI/513(Pt.2)/ 1, April 2017

6

ANNEXURE-I (Para 4.1 of the Scheme of Testing and Inspection)

XYZ IRON AND STEEL COMPANY

(Registered office Address and works address) TEST CERTIFICATE FOR COLD REDUCED CARBON STEEL SHEET AND STRIP PART 2 HIGH TENSILE AND MULTI-PHASE STEEL

TEST CERTIFICATE No.________________________________________________________________________________DATE_________ To M/s_____________________________________________________________________________________________________________

It is certified that the material described below fully conforms to IS 513(part 2):2016 Chemical composition and Mechanical

properties of the product, as tested in accordance with the Scheme of Testing and Inspection contained in the BIS Certification Marks

Licence No.CM/L_____________________ are as indicated below against each order No. etc.

(PLEASE REFER TO IS 513(part2):2016 FOR DETAILS OF SPECIFICATION REQUIREMENTS)

TEST RESULTS

Order

No.

Dime

nsio

ns

Cast No.

& C.U.

No.

Nomencl

ature of

steel

grade

quality

Quanti

ty

(Tonn

es)

Chemical Analysis n +Surface

roughness

Surface

Condition &

Finish C

(%) S

(%)

P

(%)

N

(%)

Yield Stress

(N/mm2)

Tensile Strength

(N/mm2)

Elongation

(%)

The material supplied conforms to the stipulated rolling tolerances. + If required by the purchaser Remarks:

SIGNATURE DESIGNATION FOR XYZ

IRON & STEEL COMPANY

(It is suggested that size A-4 paper (210X297) be used for this certificate)

BIS

STANDARD

MARK

Page 19: केय म ुहर वभाग-2 हमारा संदभ : सीएमडी-2/16:513 (भाग 1 एवं 2) 19 … · In IS 513 (part2):2016, for automobile and engineering

DOC: STI/513(Pt.2)/1 April 2017

PROFORMA FOR OBTAINING PRODUCTION DETAILS

Period covered

Name of Licensee

Name of Articles (s) IS No.

Grade/Type/Size/Variety/Class/Rating

Brand/Trade/Name(s) of Product covered under BIS Certification Mark

Total production of the articles(s) licensed for certification marking

Total production of the article(s) conforming to Indian Standard

Production covered with BIS Certification Mark and its Value :

a) Quantity

Brand Name used on production covered under BIS Certification Mark

Calculation of marking fee on unit-rate basis; Marking Fee per unit

a) Unit

b) Quantity covered with BIS Certification Mark

c) Marking fee rounded off in whole rupees as obtained by applying unit rates given in (a) on quantity

given in (b)

Quantity not covered with BIS Certification Mark, if any.

Reasons for such non-coverage

Brand Name under which non-ISI goods were sold

Quantity exported with BIS Standard Mark and its value

Brand Name under which BIS Certified goods are exported

Authentication by Chartered Accountant

7

Page 20: केय म ुहर वभाग-2 हमारा संदभ : सीएमडी-2/16:513 (भाग 1 एवं 2) 19 … · In IS 513 (part2):2016, for automobile and engineering

Annex-3

Significant changes in IS 513 (Part 1):2016

clause Requirement

1 It covers sheets and strips up to 4.0 mm thick both in coil form and cut lengths

3.2 New designations and grades are added

Classification of grades has been added

4.3 New designations have been added in temper designations

5.3 Non-ageing characteristics have been modified

7&8 chemical composition, variation in product analysis and mechanical properties

are changed as per the new designations and grades;

9,10 &

11

mechanical and physical properties, surface finish, freedom from defects and

dimensions and tolerances have been modified.

Significant changes in IS 513 (Part 2):2016

clause Requirement

1 It covers sheets and strips up to 3.0 mm thick both in coil form and cut lengths

3.2 Classification of grades has been added

6 & 7 chemical composition, variation in product analysis and mechanical properties

are changed as per the new designations and grades;

8,9 &

10

mechanical and physical properties, surface finish, freedom from defects and

dimensions and tolerances have been modified.

Page 21: केय म ुहर वभाग-2 हमारा संदभ : सीएमडी-2/16:513 (भाग 1 एवं 2) 19 … · In IS 513 (part2):2016, for automobile and engineering

CENTRAL MARKS DEPARTMENT-2

Our Ref.: CMD-II/16: 513(part 1) 18 05 2017

Subject: Grouping Guidelines for certification of Cold Reduced Carbon Steel Sheet and

Strip part 1 cold forming and drawing purpose as per IS 513 (part 1): 2016

Table 1 of IS 513(part 1):2016 specifies different steel Quality Designations and Grades of Steel

that may be produced as per IS 513(part 1): 2016. Clause 11 of IS 513(part 1): 2016 specifies the

Dimensions and Tolerances of the Sheets/Strips to be supplied as per IS 513(part 1): 2016.

Further, Cl.4.3 of IS 513(part 1): 2016 specifies the various Temper Conditions and Cl. 9.5 of IS

513(part 1): 2016 specifies the various Surface conditions of the Sheets/Strips to be supplied as

per IS 513(part 1): 2016.

1. In order to follow a uniform policy in the drawl of samples for independent testing for the

purpose of grant of license/ inclusion of additional varieties in the existing license, the

following procedure is to be followed:

Group Designation(Quality) Grade No of sample

1 Cold Rolled CR0 i) One sample of any size of the

Grade may be drawn.

2 General Purpose CR1,CR 2

CR3,CR4& CR5

i) One sample of any size of any

Grade may be drawn. If sample is

tested for grade of lower tensile

strength and higher drawability(r) &

stretch-ability(n),the recommendation

may include Grades with higher

tensile strength and lower

drawability(r) & stretch-ability(n)

also.

ii) For example, Sample of CR5

should be drawn to cover CR1 to

CR5.

3 Drawing Quality ISC260G,ISC270C,

ISC270D,ISC270E

ISC270F.

i) One sample of any size of any

Grade may be drawn. If sample is

tested for grade of higher minimum

tensile strength and higher

drawability(r) & stretch-ability(n),

then the recommendation may

include lower Grades also.

ii) For example, Sample of ISC270F

should be drawn to cover ISC260G to

ISC270F.

Annex-4

Page 22: केय म ुहर वभाग-2 हमारा संदभ : सीएमडी-2/16:513 (भाग 1 एवं 2) 19 … · In IS 513 (part2):2016, for automobile and engineering

4 Interstitial Free-High

Strength steel

ISC340P,ISC370P

ISC390P,ISC440P

i) One sample of any size of any

Grade may be drawn. If sample is

tested for grade of higher minimum

tensile strength then the

recommendation may include lower

Grades also.

ii) For example, Sample of ISC440P

should be drawn to cover ISC340P to

ISC440P.

5 Bake Hardening ISC270B,ISC300B

ISC320B,ISC340B,

ISC360B,ISC390B

,ISC440B

i) One sample of any size of any

Grade may be drawn. If sample is

tested for grade of higher minimum

tensile strength then the

recommendation may include lower

Grades also.

ii) For example, Sample of ISC440B

should be drawn to cover ISC270B to

ISC440B.

6 Re-phosphorized ISC280R,ISC320R,

ISC360R,ISC400R

i) One sample of any size of any

Grade may be drawn. If sample is

tested for grade of higher minimum

tensile strength then the

recommendation may include lower

Grades also.

ii) For example, Sample of ISC400R

should be drawn to cover ISC280R to

ISC400R.

7 C,Mn Steel ISC340W,ISC370W

ISC390W,ISC440W

i) One sample of any size of any

Grade may be drawn. If sample is

tested for grade of higher minimum

tensile strength then the

recommendation may include lower

Grades also.

ii) For example, Sample of ISC440W

should be drawn to cover ISC340W

to ISC440W.

Page 23: केय म ुहर वभाग-2 हमारा संदभ : सीएमडी-2/16:513 (भाग 1 एवं 2) 19 … · In IS 513 (part2):2016, for automobile and engineering

2. During preliminary inspection, before drawing samples for independent testing, it shall be

ensured by IO that tests for Dimensions and Tolerances as per cl.11 of IS 513(Pt.1):2016

shall be carried out at factory premises on the samples to be drawn for independent testing as

it is difficult to transport bulky samples to laboratory. In case of inclusion, factory test report

for Dimensions and Tolerances as per cl.11 of IS 513(Pt.1):2016 may be accepted and

conformity of the grades included to the same has to be verified during next surveillance

visit.

3. The sample tested may be any of the sizes (see Cl.11), Surface condition ( cl.9.5) and

Temper condition (see Cl.4.3) as mentioned in the specification. It is to be ensured that at

least one sample of bright finish is to be drawn/tested in case applicant/licensee has applied

for bright finish. If the sample passes, the licence/inclusion can be granted for all the sizes,

temper conditions and surface finishes (cl.9.5) mentioned in the specification and as applied

by the applicant/licensee, provided that the firm is having all necessary manufacturing and

testing facilities for manufacture and testing of all other sizes, Temper conditions and

surface finishes of sheets/strips proposed to be included in the licence.

4. The scope of licence shall clearly indicate grades, thickness range, maximum width, temper

condition (as applicable), and surface finish class based on Manufacturing/Testing facilities.

5. During the operation of licence, BO shall ensure that all the grades, sizes, temper conditions

and surface conditions of sheets/strips covered in the license are drawn for independent

testing on rotation over a period of time.

( Arun Pucchakayala)

Scientist-C,CMD-2

Head (CMD-2)(sd/-)

All ROs BOS

Page 24: केय म ुहर वभाग-2 हमारा संदभ : सीएमडी-2/16:513 (भाग 1 एवं 2) 19 … · In IS 513 (part2):2016, for automobile and engineering

CENTRAL MARKS DEPARTMENT-2

Ref.: CMD-II/16: 513(part 2) 18 05 2017

Subject: Grouping Guidelines for certification of Cold Reduced Carbon Steel Sheet and

Strip part 2 High Tensile and Multi-phase steel as per IS 513 (part 2): 2016

Table 1 of IS 513(part 2):2016 specifies different steel Quality Designations and Grades of Steel

that may be produced as per IS 513(part 2): 2016. Clause 10 of IS 513(part 2): 2016 specifies the

Dimensions and Tolerances of the Sheets/Strips to be supplied as per IS 513(part 2): 2016.

Further, Cl.8.4 specifies Surface Conditions and Cl. 8.5 specifies various Surface finishes of the

Sheets/Strips to be supplied as per IS 513(part 2): 2016.

1. In order to follow a uniform policy in the drawl of samples for independent testing for the

purpose of grant of license/ inclusion of additional varieties in the existing license, the

following procedure is to be followed:

Group Designation(Quality) Grade No of sample

1 High Strength Low

Alloy

ISC310LA,ISC320LA

ISC350LA,ISC380LA

ISC410LA,ISC440LA

ISC470L,ISC510LA

ISC550L,ISC590LA

ISC600LA,ISC700LA

ISC860LA

i) One sample of any size of

any Grade may be drawn. If

sample of higher minimum

tensile strength is tested then

the recommendation may

include grades of lower

minimum tensile strength also.

ii) For example, to cover

ISC310LA to ISC860LA,

sample of ISC860LA should be

drawn for independent testing.

2 C, Mn Steel ISC490W,ISC540W

ISC590W i) One sample of any size of

any Grade may be drawn. If

sample of higher minimum

tensile strength is tested then

the recommendation may

include grades of lower

minimum tensile strength also.

ii) For example, Sample of

ISC590W should be drawn to

cover ISC490W to ISC590W.

Annex-5

Page 25: केय म ुहर वभाग-2 हमारा संदभ : सीएमडी-2/16:513 (भाग 1 एवं 2) 19 … · In IS 513 (part2):2016, for automobile and engineering

3 Dual Phase steel ISC450Y ,ISC490Y

ISC540Y ,ISC590YL

ISC590Y,

ISC780Y,ISC980YL

,ISC980Y

,ISC1180Y

ISC1180YL

i) One sample of any size of

any Grade may be drawn. If

sample of higher minimum

tensile strength is tested then

the recommendation may

include grades of lower

minimum tensile strength also.

ii) For example, sample of any

of the grades ISC1180YL

should be drawn to cover

ISC450Yto ISC1180YL.

4 Dual Phase steel ISC590YH ,ISC780YH

ISC980YH,ISC1180YH

i) One sample of any size of

any Grade may be drawn. If

sample of higher minimum

tensile strength is tested then

the recommendation may

include grades of lower

minimum tensile strength also.

ii) For example, sample of any

of the grades ISC1180YH

should be drawn to cover

ISC590YHto ISC1180YH.

5 TRIP Steel ISC590T,ISC690T,

ISC780T i) One sample of any size of

any Grade may be drawn. If

sample of higher minimum

tensile strength is tested then

the recommendation may

include grades of lower

minimum tensile strength also.

ii) For example, Sample of

ISC780T should be drawn to

cover ISC590T to ISC780T

6 Complex Phase Steel ISC600C,ISC780C,ISC980C i) One sample of any size of

any Grade may be drawn. If

sample of higher minimum

tensile strength is tested then

the recommendation may

include grades of lower

minimum tensile strength also.

ii) For example, Sample of

ISC980C should be drawn to

cover ISC600C to ISC980C.

Page 26: केय म ुहर वभाग-2 हमारा संदभ : सीएमडी-2/16:513 (भाग 1 एवं 2) 19 … · In IS 513 (part2):2016, for automobile and engineering

7 Martensitic Steel ISC900M,ISC1100M,

ISC1300M, ISC1500M i) One sample of any size of

any Grade may be drawn. If

sample higher minimum tensile

strength is tested then the

recommendation may include

grades of lower minimum

tensile strength also.

ii) For example, Sample of

ISC1500M should be drawn to

cover ISC1500M to ISC900M.

8 Hot forming grades ISC480HF i) One sample of any size may

be drawn to cover all sizes in

the grade.

2. During preliminary inspection, before drawing samples for independent testing, it shall be

ensured by IO that tests for Dimensions and Tolerances as per cl.10 of IS 513(Pt.2):2016

shall be carried out at factory premises on the samples to be drawn for independent testing as

it is difficult to transport bulky samples to laboratory. In case of inclusion, factory test report

for Dimensions and Tolerances as per cl.10 of IS 513(Pt.2):2016 may be accepted and

conformity of the grades included to the same has to be verified during next surveillance

visit.

3. The sample tested may be any of the sizes (see Cl.10) and Surface condition (see Cl.8.4) as

mentioned in the specification. It is to be ensured that at least one sample of bright finish is

to be drawn/tested in case applicant/licensee has applied for bright finish. If the sample

passes, the licence can be granted for all the sizes and surface finishes (cl.8.5) mentioned in

the specification and as applied by the applicant/licensee, provided that the firm is having all

necessary manufacturing and testing facilities for manufacture and testing of all other sizes

and surface finishes of sheets/strips proposed to be included in the licence.

4. The scope of licence shall clearly indicate grades, thickness range, maximum width, and

surface finish class based on Manufacturing/Testing facilities.

5. During the operation of licence, BO shall ensure that all the grades and sizes of sheets/strips

covered in the license are drawn for independent testing on rotation over a period of time.

( Arun Pucchakayala)

Scientist-C,CMD-2

Head (CMD-2)(sd/-)

All ROs BOS