7/28/2019 Florprime Dpm

1/2

FLORPRIME DPM

DAMP PROOF EPOXY PRIMER

Product Description

FLORPRIME DPM is a two components, solvent free,epoxy resin, liquid applied surface damp proofmembrane.

Features

Reduces project timescale Impervious to water Excellent adhesion to concrete and screeds Tolerates upto 99% Relative Humidity in the concrete

or screed substrate.

Easy to apply Solvent free; low odour.

Green Building Compliance

This product is Eco-friendly, Low VOC, solvent free witha high level of mechanical, chemical resistance, ideal foruse in Green Building.

Uses

Allows immediate installation of moisture sensitive floorfinishes onto concretes and screeds which havemoisture content up to 99% Relative Humidity.

Properties

Application : By squeegee and Roller

Mixing ratio : As supplied

Pot Life : 40 mins @ 20 C& 20 Minutes @30

oC

Curing Time :Initial Cure 4-5 hours,Full Mech. Cure 12 hoursReady for use Within 24hrsTop coat

Recommended No. of coats : 2 Minimum

The values given above are average figures achieved in

laboratory tests. Actual values obtained on site mayshow minor variations from those quoted.

Coverage

FLORPRIME DPM:

Approximately 2sqm /kg /two coats depending

on substrate porosity, texture, temperature of substrate.

Method of Application

APURVAs system should be installed by approvedcontractors. Following information should be used as aguideline.

1. TemperatureFLORPRIME DPM should not be applied at material orfloor temperatures below 10

oC. Temperatures should

not fall below 5oC in the 24 hrs after application.

2. Substrate requirementMust be of sufficient strength to support loads appliedthrough the topping.

All contamination must be removed to give a clean drytextured surface.

3. RepairsAll damaged areas of floor should be made good and upto level with Epoxy Mortar applied over wet FLORPRIMEDPM. Top coat should be applied after FLORPRIMEDPM hard dry i.e. after overnight.

4. Substrate movementAll moving joints must be carried through theFLORPRIME DPM and properly sealed. Construction

joints and cracks may be covered but if substratemovement occurs, the FLORPRIME DPM will reflect thecrack.

Mixing:

Pack components are pre-weighed for optimumperformance. Never split packs. Empty contents ofcomponent B into a mixing container and pre-mix toassure the suspension of solids. Add component A andcontinue to mix to a uniform consistency for 1-2 minutes.Mix with slow speed drill and helical spinner head for 2minutes.

Application

FLORPRIME DPM must be applied immediately aftermixing the two components. FLORPRIME DPM isapplied with a paint brush or roller to produce a thin film.

Packaging

FLORPRIME DPM is available in 6Kg composite packsfor easy handling.

7/28/2019 Florprime Dpm

2/2

Shelf life

FLORPRIME DPMhas a shelf life of 12 months if kept in

warehouse conditions at 30C in the original, unopened

pack.

Storage conditions

Store in dry conditions between 5oC and 30oC, awayfrom sources of heat and naked flames, in the original,unopened packs. If stored at high temperatures the shelflife will be reduced.

NB : If materials are stored for more than 1 monthwithout movement, some settlement in Basecomponents can occur. It is recommended that thecontents are turned 180 degrees from top to bottomevery month during storage.

Handling & Safety

Keep the containers tightly sealed when not in use.Avoid skin contact and inhalation of fumes ( if any). Whilespraying it is advised to wear a mask. If it comes incontact with the body, wash affected parts with plenty ofwater. In case of persistent irritation, contact a physician.

Disclaimer: The manufacturer reserves the right to change thespecifications. Apurva India Limited products are guaranteed againstmaterial manufactured and are sold subject to the companys Terms andConditions of Sale. Whilst we endeavour to ensure that advice,specifications, recommendations and information given is correct, wecannot have control over how our products are applied and will notaccept liability, directly or indirectly, arising from application of ourmaterials.