beton prategang

Creating

Solutions

Together

FLY OVER KUALANAMU - MEDAN

FLY OVER KUALANAMU MEDAN – SUMATRA

UTARA

Creating

Solutions

Together


SCOPE OF WORKS

VSL’s scope of works are :

a. SUPPLY of MATERIALS AND EQUIPMENTS of PRESTRESSING WORKS (excluding strand)

b. INSTALLATION (excluding bursting steel, support bar)

c. STRESSING

d. GROUTING (excluding cement)

Creating

Solutions

Together


STRAND

MATERIAL SPECIFICATION

Creating

Solutions

Together


DUCT

Material ini berfungsi sebagai pembungkus strand, dengan bahan dasarnya adalah Galvanized Zinc yang dibentuk berupa pipa berulir :

Creating

Solutions

Together


LIVE ANCHORAGE

Creating

Solutions

Together


DEAD END ANCHORAGE

Creating

Solutions

Together


ADDITIVE FOR GROUT

Creating

Solutions

Together


EQUIPMENT SPECIFICATION

Creating

Solutions

Together


GROUT PUMP

Technical Data :

Power : 5.5 HPMax. Pressure : 10 BarVoltage : 380 VoltCapacity : 8 BagDelivery : 40 Liter/min

Creating

Solutions

Together


FLOW CHART

Creating

Solutions

Together


SPESIFIKASIGAMBAR KERJA

MATERIAL PABRIKASI STRAND INSTALASI STRAND KALAU ADA, INSTAL LIFTING HOOK

PEMASANGAN ANGKUR HIDUP DAN ANGKURMATI

INSPEKSI BERSAMA KONTRAKTOR

PENGECORAN

KUAT BETON PADA SAAT TRANSFER

STRESSING

EVALUASI HASIL STRESSING

GROUTING

SELESAI

MENUNGGU KUAT BETON PADASAAT TRANSFER TERCAPAI

TIDAK

OK

TIDAK

TIDAK

ALUR KERJ A PEKERJ AANPRESTRESSING

FLOW CHART

Creating

Solutions

Together


SHOP DRAWING

Creating

Solutions

Together


INSTALLATION

Creating

Solutions

Together


1.1. Pemasangan pembesian balok Pemasangan pembesian balok

Creating

Solutions

Together


2. 2. Pengukuran ordinat tendon Pengukuran ordinat tendon

Creating

Solutions

Together


3. 3. Pemasangan support bar pada posisi yang telah Pemasangan support bar pada posisi yang telah diberi marking.diberi marking.

Creating

Solutions

Together


4.4. Penempatan duct pada setiap support bar.Penempatan duct pada setiap support bar.5.5. Menyambung duct dengan duct coupler.Menyambung duct dengan duct coupler.

Creating

Solutions

Together


6. Memasang angkur hidup (Casting)6. Memasang angkur hidup (Casting)7. Memastikan semua ordinat tendon telah berada 7. Memastikan semua ordinat tendon telah berada pada posisinya.pada posisinya.

Creating

Solutions

Together


8.8. Pemeriksaan bersama kontraktor dan Pemeriksaan bersama kontraktor dan konsultankonsultan

9.9. Perbaikan jika diperlukan.Perbaikan jika diperlukan.10. Pengecoran.10. Pengecoran.

Creating

Solutions

Together


STRESSING

Creating

Solutions

Together


CCOMPRESSIVE COMPRESSIVE CONCRETE STRENGTH !!ONCRETE STRENGTH !!

STRESSING

Creating

Solutions

Together


stressing tendon dapat dilakukan

Jika

Kuat Tekan Test Beton mencapai minimum 80% dari kriteria design

Kecuali tersebut dalam spesifikasi

STRESSING

Creating

Solutions

Together


STRESSING

GENERAL STRESSING THEORY

Creating

Solutions

Together


1. Perhitungan Jacking force 1. Perhitungan Jacking force

2. Persiapan peralatan stressing2. Persiapan peralatan stressing

3. Memasang anchor head dan wedges3. Memasang anchor head dan wedges

4. Memasang chair block.4. Memasang chair block.

5. Memasang jack hingga rapat anchor block5. Memasang jack hingga rapat anchor block

6. Memberikan gaya awal sebesar 5 mpa. untuk 6. Memberikan gaya awal sebesar 5 mpa. untuk merapatkan segmenmerapatkan segmen

7. Pencatatan gaya pada manometer dan elongasi7. Pencatatan gaya pada manometer dan elongasi

8. Persetujuan hasil stressing 8. Persetujuan hasil stressing

9. Menutup anchor head dengan mortar semen 9. Menutup anchor head dengan mortar semen (parging)(parging)

Creating

Solutions

Together


Persiapan stressing bed

Pemasangan anchor block dan wedges

Creating

Solutions

Together


Instalasi Hydraulic jackPenyetelan gripper plate dan

pemasangan T device

Creating

Solutions

Together


Pemasangan busa pelindung duct dan pemberian epoxy pada sambungan segmen

Creating

Solutions

Together


Pelaksanaan stressing

Creating

Solutions

Together


Pengukuran elongation

Creating

Solutions

Together


Creating

Solutions

Together


STRESSING PROCEDURE (MULTISTRAND)

Creating

Solutions

Together


METODA STRESSING SECARA UMUM :

1. ONE ENDArti : Stressing 1 unit tendon dilakukan pada 1 arah dengan

menggunakan 1 alat

2. BOTH ENDArti : Stressing 1 unit tendon dilakukan pada 2 arah secara

bersamaan dengan menggunakan 2 alat

3. TOP UPArti : Stressing 1 unit tendon dilakukan pada 2 arah secara

bergantian dengan menggunakan 1 atau 2 alat

Creating

Solutions

Together


TAHAPAN STRESSING :

1. Stage I : up to 25% of Final Jacking Force

2. Stage II : up to 50% of Final Jacking Force

3. Stage III : up to 75% of Final Jacking Force

4. Stage IV : up to 100% of Final Jacking Force

5. Stage V : Release force down to 5% of Final Jacking Force

Creating

Solutions

Together


WHEN EVERYTHING IS READY, STRESSING MAY BEGIN

Creating

Solutions

Together


STRESSED TENDON AT ONE END ONLY (passive side is live end)

END AEND A

LL

STRESSED TENDON AT ONE END ONLY

Creating

Solutions

Together


Creating

Solutions

Together


STRESSING TENDON UP TO 25% OF FINAL JACKING FORCE

Creating

Solutions

Together


MEASURED ELONGATION AND CEK WEDGE DRAW IN AT PASSIVE SIDE (IF ANY)

Creating

Solutions

Together


1.) RECORD ELONGATION READING AT 25% OF FINAL JACKING FORCE

Creating

Solutions

Together


RELEASE PRESSURE TO ZERO AND RETRACT PISTON

Creating

Solutions

Together


PULL JACK BACKWARD SLIGHTLY AND SPRAY MARK AT BUNDLE STRAND WHERE ARE FACING ON ANCHOR HEAD

Creating

Solutions

Together


PUSH JACK TOWARD ANCHOR HEAD

Creating

Solutions

Together


STRESSING TENDON UP TO 50% OF FINAL JACKING FORCE, MEASURED ELONGATION.RECORD ELONGATION READING AT 50% OF FINAL JACKING FORCE.(calculated the elongation between 25% and 50% by deducting 25% value from 50% value and record that value)

Creating

Solutions

Together


Creating

Solutions

Together


RELEASE FORCE DOWN TO 5% OF FINAL JACKING FORCE , MEASURED ELONGATION.RECORD READING ELONGATION AT 5% OF FINAL JACKING FORCE.

Creating

Solutions

Together


Creating

Solutions

Together


CALCULATION ELONGATION

Creating

Solutions

Together


Value of “adjustment jack (mm)” are based on the jack will be used during stressing.

Formula for Adjustment Jack = P L / n E A

Example :Type jack : ZPE 460L jack : 58 cmP jacking (100% JF) : 4028 KN = (4028 x 1000)/9.81 = 410601.427 kg n strand : 19 (0.6’)A strand : 1.5 cm2E strand : 1.95 x 106 kg/cm2

Adjustment Jack = (410601.427 x 58) / (19 x 1950000 x 1.5)= 0.42 cm = 4 mm

Value of “adjustment draw in a (mm)” and “adjustment draw in b (mm)” are based on VSL system, where ; a : draw in wedges at active side = 6 mm b : draw in wedges at passive side = 2 mm

Creating

Solutions

Together


Elongation

calculated before

lock-off

Elongation

calculated after

lock-off

0mm -6mm Wedge seating in stressing end

-4mm -4mm Elongation in jack

-2mm -2mm Wedge seating in dead end

+6mm 0 Wedge seating in stressing end

0 0 Elongation in jack

-2mm -2mm Wedge seating in dead end

Engineer

Elongation measured

before lock-off

Elongation measured

after lock-off

Multi

Single

Creating

Solutions

Together


Creating

Solutions

Together


Tujuan Grouting :

Mencegah korosi didalam Tendon

Sebagai kekuatan ikatan antara Tendon dan Beton

GROUTING

Creating

Solutions

Together


Pemilihan materials semen, air, additive yang sesuai dengan spesifikasi

Kontrol terus menerus untuk memastikan hasil dan campurannya sesuai.

Pelaksanaan Grouting dilaksanakan oleh orang yang sudah berkompeten

Kualitas dari Grouting dapat dicapai dengan :

Creating

Solutions

Together


Komposisi material penyusun grout :

Semen : 1 bag (50 kg)

Air : 0,40 – 0,45 dari berat semen

20 – 22,5 liter / sak semen

Admixture : 0.45 % dari berat semen

200 – 225 gram / sak semen

Creating

Solutions

Together


Compressive Strength test

a. Test dilakukan pada sample kubus Grouting

b. Alat yang digunakan :

o Metal moulds 50 mm x 50 mm x 50 mm

o Compressive test machine

o Glass plate

o Steel ruler

Creating

Solutions

Together


c. Prosedur :

o Pour fresh grout into the mould. The sample shall not be subject to any vibration. Immediately strike off the excess grout with steel ruler slowly in each direction. Then cover the sample with a glass plate. Give mark on mould to identify the sample.

o Sample harus direndam didalam air pada suhu ± 20 derajat celcius sampai saat akan dilakukan test.

o Compressive strength test dilakukan minimal pada 2 benda uji untuk satu Grouting mixing.

• Reporting : Catat hasil pengujian compressive strength untuk masing – masing

sample (N/mm2)

• Kriteria : strength ≥ 30 N/mm2 at 28 days strength ≥ 27 N/mm2 at 7 days

Creating

Solutions

Together


Thank for your attention

VSL INDONESIAVSL INDONESIAPhone: (62) 21 570 0786Phone: (62) 21 570 0786

Fax: (62) 21 573 1217 / (62) 21 573 7557Fax: (62) 21 573 1217 / (62) 21 573 7557E-mail: [email protected]: [email protected]

beton prategang

Documents